How to Reset Maintenance Required on Toyota Corolla 2017? To reset maintenance required on Toyota Corolla 2017:
Locate odometer button next to speedometer. Insert key, off position, press and hold odometer button as key turns on. Release when maintenance light goes out.
Bring car to stop, gear in ‘Park’, turn off engine. Press and hold odometer button, engine on, until maintenance light blinks and goes off. Check owner’s manual for variations. Insert key, turn to illuminate dashboard lights, find maintenance indicators.
Maintain button hold for reset. Confirm reset, turn off ignition, start engine to check. Drive to ensure light stays off. Confirm successful reset. Further steps ensure accurate maintenance reset.
Step 1: Locate the Odometer Button
To begin the process of resetting maintenance on a Toyota Corolla 2017, the first step is to locate the odometer button. This button is typically located on the dashboard near the speedometer and fuel gauge.
Once you have located the odometer button, ensure the key is in the ignition and turned to the ‘off’ position. To proceed, press and hold down the odometer button. While holding the button, turn the key to the ‘on’ position without starting the engine.
You will notice that the odometer reading changes to a series of dashes or zeros, indicating that the maintenance reset is in progress. Continue holding the button until the maintenance light on the dashboard turns off.
At this point, release the odometer button. The maintenance reset is now complete, and you have successfully cleared the maintenance light on your Toyota Corolla 2017.
This straightforward process allows you to reset the maintenance reminder without the need for a trip to the dealership.
Step 2: Turn Off the Engine
After successfully completing the maintenance reset process on your Toyota Corolla 2017, the next step is to ensure the engine is turned off before proceeding further. Turning off the engine is a crucial step to safely reset the maintenance required light. Follow these simple steps to turn off the engine:
Step | Instructions |
---|---|
1 | Bring your vehicle to a complete stop. |
2 | Put the gear shift in the ‘Park’ position. |
3 | Turn the ignition key to the ‘Off’ position. |
Step 3: Press and Hold Odometer Button
Begin by pressing and holding the odometer button in your Toyota Corolla 2017 to proceed with the maintenance reset process. Locate the odometer button on the dashboard, typically found near the speedometer.
Once you have identified the button, make sure the vehicle is in a stationary position with the engine off. Press and hold the odometer button while also turning the engine switch to the ‘On’ position without starting the engine.
You will notice the display screen cycling through different messages or symbols. Continue holding the button until the maintenance required light blinks and eventually goes out. This action signifies that the maintenance reset is complete.
Remember that this process may vary slightly depending on the specific model year of your Toyota Corolla, so always refer to the owner’s manual for detailed instructions.
Following these steps correctly should effectively reset the maintenance required light on your Toyota Corolla 2017.
Step 4: Turn Ignition On
With the vehicle in a stationary position and the engine off, proceed to turn the ignition on to initiate the next step in resetting the maintenance on your Toyota Corolla 2017.
When turning the ignition on, follow these steps:
- Insert the key into the ignition slot and ensure it is fully inserted.
- Turn the key clockwise until the dashboard lights illuminate, but do not start the engine.
- Pay attention to the dashboard display for any maintenance indicators that need to be addressed.
- Take note of any warning lights that may appear, signaling additional maintenance requirements beyond the standard reset procedure.
Step 5: Continue Holding Button Until Reset
Upon reaching the maintenance reset screen, continue holding the designated button until the reset process is initiated. Once you have successfully navigated to the maintenance reset screen in your Toyota Corolla 2017, it is crucial to maintain pressure on the designated button.
By holding the button down continuously, you ensure that the system recognizes your intention to reset the maintenance required light. This action is vital for prompting the vehicle’s onboard computer to process the reset command.
Holding the button until the reset process begins is a straightforward yet critical step in the maintenance reset procedure. It allows the system to acknowledge your input and proceed with resetting the maintenance light.
Keep a steady hand on the button during this phase to avoid any interruptions in the reset process. By following this simple instruction, you can effectively initiate the maintenance light reset on your Toyota Corolla 2017.
Step 6: Verify Maintenance Light Is Reset
After successfully initiating the maintenance light reset process on your Toyota Corolla 2017 by holding the designated button, the next step is to confirm that the reset has been completed. To verify that the maintenance light has been successfully reset, follow these steps:
- Turn Ignition Off: Ensure the ignition is turned off to begin the verification process.
- Restart the Engine: Start the engine to see if the maintenance light remains off after the reset.
- Check Dashboard: Look at the dashboard indicators to confirm that the maintenance light no longer appears.
- Take a Test Drive: For further confirmation, take your Toyota Corolla for a short drive to ensure the maintenance light stays off during normal operation.
Wrapping Up
In conclusion, resetting the maintenance required light on a Toyota Corolla 2017 is a simple process that can be done by following a few steps.
By locating the odometer button, turning off the engine, pressing and holding the button, turning the ignition on, and continuing to hold the button until the light is reset, you can easily reset the maintenance reminder on your vehicle.
Make sure to verify that the maintenance light is reset before driving.